Change the APN on a Sierra Wireless LS300

    Different cellular providers use different Access Point Names (APNs) to connect to the network. Use an Ethernet cable to connect the LS300 to the Ethernet jack on a computer Open a web browser and type the default IP address into the address bar as follows: 192.168.13.31:9191 The modem’s native AceManager will appear The default user […]

    Read More

    Hard Reset a Raven XT Modem

    There are instances such as when a modem transfers cellular accounts that require a hard reset of the device. The following process will reset the device to manufacturer’s defaults and allow it to re-register on the network. Remove both black fuses (Battery and External) to disconnect power while taking the logger apart Remove the (4) […]

    Read More

    Install Mounting Plate

    Mount the iSIC box to a wall using the A55 mounting plate. It may be attached using the included hardware. First attach the plate to the back of the iSIC box using the (4) ¼-20 X ¾” bolts and then secure the mounting plate to the support surface. It can be attached to a pole […]

    Read More

    What Is an MS2 Connector?

    An MS2 connector is used to supply power to an iSIC Data Logger. It has two openings – one for power and the other for ground. An MS2 connector can be found on the A11 float charger (power adapter) and the solar panels of iSIC MAST systems.   The port which connects the MS2 connector […]

    Read More

    Reset iSIC Data Logger to Manufacturer’s Defaults

    1. Refer to the appropriate data logger category for instructions on connecting directly to the iSIC Data Logger or SDL500 that is being used. 2. In iChart, click Advanced | iSIC | iSIC. The iSIC Setup window will appear.     3. Enter the correct COM Port (Check the Port on the Device Manager by clicking Start | Right-click […]

    Read More

    Setting an SDL500 or iSIC Data Logger as a Pass-Through Device

    In order to collect data from an iSIC that is connected to another iSIC, pass-through settings must be made in iChart. This article assumes an iChart project file and data loggers have already been programmed. 1. Right click on the data logger in the iChart Navigation Panel and select Property. The iSIC Data Logger Communication Properties […]

    Read More

    Install New Lantronix Software

    1. Uninstall the current Lantronix software. 2. Go to this link http://gridconnect.com/rs232-rj45.html and select Documentation. Click the link under Downloads to download a zip file that’s about 183 MB. 3. Extract the file. 4. Inside the Net232 folder, run the autorun.exe. 5. First run the “.NET Framework Install” if it isn’t (.NET 4) installed. 6. […]

    Read More

    Reinstalling an iSIC Circuit Board

    After repairs or diagnostics, it may be necessary to reinstall an iSIC data logger’s circuit board. 1. Mount the PCB to the mounting plate using (4) M3 x 16 screws and (4) M3 lock washers.     2. Turn the mounting plate over, place an M3 lockwasher  and an M3 hex nut on the one […]

    Read More

    Manually Sync an iSIC Data Logger Clock to the PC Clock

    NexSens iSIC data loggers incorporate a precision real-time clock. However, the clock can drift up to two minutes per month and regional time changes require the clock to be synchronized periodically. This can be done manually or automatically. Confirm that the computer clock is correct Open iChart with a current project iChart must be opened […]

    Read More

    What Kind of Charger do I use to Charge an iSIC Battery?

    The 12V DC (direct current) batteries used on NexSens iSIC data loggers can be charged in two ways: online or offline. It will be necessary to decide which is most appropriate for the desired application. The necessary charger type can then be determined. Online Charging: If it is essential for the iSIC to always remain powered, […]

    Read More